Month: August 2019

Plumbing Issues – Clogged Sinks and DrainsPlumbing Issues – Clogged Sinks and Drains

There is a series of tactics to try when your sink is stinky or clogged. First off, try putting Drainbo down the sink, (remove the trap and plug the bottom of the drain so Drainbo can sit in the pipe drain awhile and work its magic). Because Drainbo tends to eliminate things like scum, it may resolve the clog and the problem. But if it’s a big problem clog, you might need to take apart the pop up assembly to get the gunk off of it.
Sometimes the metal stopper can be pulled out of the sink without any extra tools, which is great, because you may be able to use a screwdriver to break up the clog and either pull it out or get it small enough to wash through the pipe. If you can’t pull it out, make sure it’s in small pieces before you try to wash it away, or you may wind up with a clog even further down the drain. This is important: if your sink is old, the plumbing behind it may be old too, and metal pipes may be thin enough in places to jab a wooden toothpick through their walls. If your pipes are metal and old, you can do some serious damage if you’re jabbing away with a screwdriver. So, be careful, work at the clog patiently, and keep the screwdriver from poking against the sides of the services

Once you push or pull the clog out, run the hottest water you can find through the drain to finish cleaning it out.

If the stopper doesn’t come out when you pull it, it may be attached to the pop up assembly, and you’ll have to unscrew the rod. You can find it under the sink: it has a big nut on the side, so get your wrench or a pair of pliers and unscrew the nut, which will then allow you to pull the pop up rod free of the sink. You might need to bend the place where it’s attached to get it free, but you can bend it back when you put the sink back together. More about Plumbing Repairs

When you’re doing this work, you may encounter a variety of small metal or rubber rings, called washers. Washers are used when parts join one another, and their job is to make the connection tighter, preventing leaks and keeping parts right up against each other. If you lose a washer or forget to put it back where it belongs, you’re going to wind up with a leak. And if you haven’t done plumbing or other mechanical tasks before, this is a good time to cover what experienced mechanics do automatically. When you start to take things apart, lay them out on a piece of newspaper in the order in which they were removed. That way, when you aren’t sure whether to put the widget before or after the thingamabob, you’ll be able to see which comes first. And if you have to remove parts to clean them or replace them, you may even want to take notes, so keep a pencil and paper handy too.

Once you’ve got the pop up assembly apart, use a wire brush and some oxygen bleach to scrub off the pop up and various bits and pieces, including as much of the trap pipe itself as you can get to. (Never use chlorine bleach to clean your gunky plumbing—it can mix with soaps or other chemicals and create a dangerous gas). If you really have your act together, you can add some lubricant to the pop up assembly once you’ve put it back together—use plumber’s grease. Put it on the rod where it attaches to other parts, and spread a little on the seals and threads of the pipes. Your pop up stopper will work smoothly and you’ll have an easier time the next time you take the pop up apart. Once you’ve got the whole thing back together, make sure you have replaced and tightened the nut at the underside of the sink, or you’ll wind up with a floor full of water when you start to flush the drain. Run a little water down to sink to make sure the nut is holding tight, and then pour plenty of hot, hot water down the drain. This helps any little bits of gunk that you dislodged but didn’t remove to slide down the drain.

Low flow sinks and toilets are great because they save water, but they can be prone to clogs because they don’t have the pressure gallons and gallons of water rushing through them whenever they’re being used. If you’re having continual problems with clogs, you may want to waste a little water and really give your sink a good flushing out once a month or so. Pouring some Drainbo down the sink will help keep your drains clean and clear, as much of the debris that would otherwise settle on the sides of the pipes will be digested by the microbes in Drainbo. Once the waste is made very small and broken into its organic components, it will tend to liquefy and move on out as wastewater instead of taking up residence in your drains.